Malapa MDZ3 digital programmable switchboard

The wall-mounted electronic distribution board from the MDZ series is intended for a complex solution - power supply, switching, regulation, heating control for both inductive and resistive loads. This device switches and switches off the outlet using noiseless power relays designed for the switched power of the given distribution board. The main distribution board contains a thermostat controlled heating socket with temperature settings for day and another for night.

Another outlet controlled by a thermostat together with a hygrostat and regulation is intended for exhaust/intake of air, of course with settings for day and others for night, it allows you to adjust different speeds of the fan at the set temperature and others when the set value is exceeded. To power the lighting, there are 2 switched sockets controlled by a timer, each of which can be loaded with 1x 1200W (2x 600W).

Switched sockets have a protection circuit in the event of a power failure, they will switch on for up to 10 minutes. after a blackout, the discharge lamps will cool down in the meantime and start them easier. One outlet controlled by a timer for the pumps, you program a time for watering and another for a break, the frequency of watering can be different during the day and at night. For powering other devices, the switchboard has an integrated one non-switched socket, which is under permanent voltage. Thermostats and hygrostats have adjustable hysteresis.

The clear 4-line LCD display informs you simultaneously about the temperature, time and status of the outputs (sockets). The processor constantly monitors inputs, outputs, connection with the sensor and, if necessary, signals an error optically and also acoustically. Backup settings. The temperature is measured by an accurate and reliable DALLAS digital sensor, the information is transmitted via a 1.5 meter cable extension. Immediate installation, for connection to electricity. the network is served by a 5-meter-long cord with a fork, and sockets are used to connect the device. You can fix the device on the wall with hanging brackets (included in delivery). Long-term and error-free operation even under extreme conditions, over design.

Use:

It can be used, for example, for control, regular control of pumps, thermostat for heating, lighting or lighting of greenhouses, botanical gardens, terrariums, animal husbandry.

Distribution of sockets:

- 2 x switched sockets controlled by switching clocks for lighting (each socket max. 1x 1200W or 2x 600W), with protection against power failure (10 minutes)

- 2x non-switched socket under permanent voltage

- 1x socket for the pump (time switch) for irrigation - 2 programs for day/night, various adjustable time for switching on/off, (max. 2600W)

- 1x socket for heating - thermostat, 2 programs for day/night, adjustable hysteresis (max. 2600W)

- 1x socket for fan (exhaust/supply) - hygrostat/ thermostat with regulation (with feedback) minimum/maximum speed 0% to 100%, 2 programs for day/night, adjustable hysteresis (max. 900W)

variants of the main MDZ switchboards: MDZ1 - basic MDZ2 - additional digital timer for regular control of irrigation pumps, 2 programs for day/night MDZ3 - additional digital timer for regular control of irrigation pumps, 2 programs for day/night + combined hygrostat/ thermostat with regulation for the fan extension with additional MZP switchboards:

Each main digital programmable switchboard can control additional switchboards MZP1, MZP2, MZP3. Additional distribution boards differ from each other in the number of sockets and connection to the network. One main switchboard can control up to 20 auxiliary switchboards. advantages: It remembers the settings even after a power cut. energy, quick changes in settings and accurate measurement of all quantities, negligible consumption, continuous temperature without fluctuations, pleasant climate, less mechanical/thermal stress on mechanical components, high coverage of the device, communication with the sensor takes place with a safe voltage.

An appliance that is not running does not consume any electricity. energy. installation: The sensor on the cable can sense the temperature in a different space or in the air distribution than the one where the device is located. We recommend placing the sensor approx. 1.5 m. above the ground in a place with good air circulation, do not place the sensor near heat radiators. hysteresis: temperature and humidity difference or inertia when the device switches humidity reduction on and off - e.g. if the hysteresis is 1%RH, the desired humidity is 20%RH, the hygrostat switches off at 21%RH and switches on again at 20%RH humidification - e.g. if it is hysteresis 1%RH, desired humidity 20%RH, hygrostat turns off at 19%RH and turns on again at 20%RH heating - e.g. if hysteresis is 1°C, desired temperature 20°C, thermostat turns off at 21°C and turns on again at 20°C cooling - e.g. if the hysteresis is 1°C, the desired temperature is 20°C, the thermostat switches off at 19°C and switches on again at 20°C.

At your request, we can also supply other variants

Technical data of the MDZ3 digital switchboard:

power supply - 230V AC 50Hz

maximum load - resistive 3600W (16A)

2x switched socket - a total of 2x 1200W or 4x 600W inductive loads (each socket max. 1x 1200W or 2x 600W), protective circuit to protect discharge lamps (10 minutes)

2x non-switched sockets under permanent voltage

1x socket for pump (time switch) - 2 programs for day/night, various adjustable time for switching on/off 1 second to 24 hours, maximum 2600W 1x socket for heating - thermostat, 2 programs day/night, maximum 2600W 1x socket for fan (exhaust/supply) - thermostat + hygrostat with regulation (with feedback) minimum/maximum speed 0% to 100%, 2 programs for day/night, maximum 900W

temperature sensor - digitally calibrated - from the manufacturer DALLAS

sensor length - 1.5 meters

sensor size - 50mm x 36mm x 15mm

LCD display - 4 lines control button - 3x (+ - SET) temperature/humidity range - 0° to 100°C, 0% to 100%RH sensor working temperature/humidity 0° to 80°C, 0% to 100%RH (non-condensing) temperature/humidity hysteresis - 1° to 10°C, 1% to 10%RH temperature/humidity tolerance +-0.25°C, +-3%RH time tolerance +-2 minutes/month time backup - battery 100 hours

data backup - 35 years

output for additional switchboard - yes

protection - thermal (switched sockets)

electronic menu - Czech (on request Germany, English, Spain)

supply cord with fork - 3 meters

mounting - wall (bracket)

total weight - 2320g

size - length 225, width 180, height 100mm working temperature -20° to 70°C

working humidity - 0% to 90%RH (non-condensing)

storage temperature - 0° to 45°C

protection - IP44

box - ABS RoHS